Nintendo Switch Joycon CNC 機械加工ハウジング
Nintendo Switch (ジョイコン) 用の完全 CNC 機械加工アルミニウム DIY ハウジングセット。これは OEM スイッチ電子機器に適合するように設計された、左右両方のフロントおよびリア ハウジングのセット(4 つの部分) 。
特徴
- 軽い質感の仕上がり
- Dパッド 左のジョイコン
- 小ネジが必要です（付属）。使用するのは長め(5mm)の留め具2本のみ！
- ジョイコンを本体から取り外しても、ワイヤレス接続は完全に機能しますが、Amiibo はそうではありません。
- アルミボタン 十字キーセットもございます！ 当社のボタンを購入するか、D-パッドが付いているプラスチックのセットを購入する必要があります。 注意: アフターマーケット キットには標準の方向パッド サイズはありませんが、eXtremeRate ジョイコンにはボタン付きのプラスチック製ジョイコン キットが付属しています。十字キーとA、B、X、Yボタンはテスト時点ではフィットします。注: eXtrmeRate 社は、いつでも寸法設計の変更を行うことができます。
- ファスナーネジサイズ：M1.4x0.3（長さ2m、3mm、5mm）
私たちのを参照してください 組み立てガイド ジョイコンの構築に役立ちます。これは、正しい留め具が使用されていることを確認するために当社のガイダンスを参照することが重要です。プラスチック製ジョイコンの純正ネジは使用しないでください。意図的に長い (5mm) 留め具が 2 ～ 3 つだけ含まれています。
これは、正しい留め具が使用されていることを確認するために当社のガイダンスを参照することが重要です。プラスチック製ジョイコンの純正ネジは使用しないでください。
すべての Switch 製品を表示するには
を参照してください。さらに質問がある場合は、 FAQ ページをご覧ください。
留め具は非常に小さいため、組み立てる際には細心の注意を払う必要があることに注意してください。最も経験豊富なビルダーであっても、簡単に問題に遭遇する可能性があります。組み立てを行う前に、必ず最初にフロントハウジングとリアハウジングを一緒に組み立てるテストを慎重に行ってください。シェルをねじ込むときに抵抗を感じる必要はありません。ネジが潰れたり、折れたり、固着したりした場合は、交換部品をご利用いただけません。詳しい手順については、組み立てガイドに従ってください。残念ながら、パーツはセットで製造され陽極酸化処理されているため、販売用のスペアパーツはありません。
Notes
These parts are not mass produced and we use multiple machine shops, so surface finish, texture, and color may vary between batches. Colors may also look different depending on your screen, the lighting, and variations in anodizing.
Please be sure to review our refund policy for cancelled and returned orders.
We cannot change the value of the shipment and sadly we do not have control over your particular country's fee/tariffs/taxes.
Brass parts come as machined and may show oxidation/discolor (due to being exposed to air) and some small machining or small scratches may be present. Assume you will need to do your final surface finishing using a flexible 3M sanding pad. (The 3M 7448 usually works well). After polishing, clean and apply clearcoat, poly, or other coating to maintain the shine. Note Brass is also very dense (heavy) and conductive. Consider in some applications, these attributes may have adverse effects. (ex. The SP hinges will not support the screen as well). If used with electronics, it is advisable to use kapton tape, insulating paint, (nail polish may work) to prevent electrical shorts.
Resources
Out of stock? Signup for our out of stock notification on this product page and check our product availability page
Assembly Instructions
International Customers
We are located in the USA, and want everyone in the world to experience Boxy Pixel products worldwide! It is important to understand a few points:
1. There are two shipping methods available. DHL and USPS (United States Postal Service). DHL is very fast and comes with insurance, but can be expensive. The USPS slow shipping we offer can take many weeks, is not reliable, and is not insured.
2. If you do choose uninsured USPS for your international shipping, we do offer third party insurance to help in case it gets lost. This is "route" insurance. It is not expensive, and is worth the cost. Deselecting this option at checkout will waive all insurance. If your package is lost, we unfortunately cannot send a refund or replacement.
3. If an item gets shipped back to us due to delivery problems, we would need to charge additional fees if you would like to attempt delivery again.
4. Return shipping is the responsibility of the buyer
5. We are prohibited from shipping batteries outside of the USA.
These parts are not mass produced and we use multiple machine shops, so surface finish, texture, and color may vary between batches. Colors may also look different depending on your screen, the lighting, and variations in anodizing.
Please be sure to review our refund policy for cancelled and returned orders.
We cannot change the value of the shipment and sadly we do not have control over your particular country's fee/tariffs/taxes.
Brass parts come as machined and may show oxidation/discolor (due to being exposed to air) and some small machining or small scratches may be present. Assume you will need to do your final surface finishing using a flexible 3M sanding pad. (The 3M 7448 usually works well). After polishing, clean and apply clearcoat, poly, or other coating to maintain the shine. Note Brass is also very dense (heavy) and conductive. Consider in some applications, these attributes may have adverse effects. (ex. The SP hinges will not support the screen as well). If used with electronics, it is advisable to use kapton tape, insulating paint, (nail polish may work) to prevent electrical shorts.
Out of stock? Signup for our out of stock notification on this product page and check our product availability page
Assembly Instructions
We are located in the USA, and want everyone in the world to experience Boxy Pixel products worldwide! It is important to understand a few points:
1. There are two shipping methods available. DHL and USPS (United States Postal Service). DHL is very fast and comes with insurance, but can be expensive. The USPS slow shipping we offer can take many weeks, is not reliable, and is not insured.
2. If you do choose uninsured USPS for your international shipping, we do offer third party insurance to help in case it gets lost. This is "route" insurance. It is not expensive, and is worth the cost. Deselecting this option at checkout will waive all insurance. If your package is lost, we unfortunately cannot send a refund or replacement.
3. If an item gets shipped back to us due to delivery problems, we would need to charge additional fees if you would like to attempt delivery again.
4. Return shipping is the responsibility of the buyer
5. We are prohibited from shipping batteries outside of the USA.
Give your Classic electronics a new life!
Unique
Parts cut from a solid block of billet aluminum
Protection
Each part is anodized for long lasting protection