PAM8302A Audio Amplifier
Small mono amp is surprisingly powerful for its size, and efficient - able to deliver up to 2.5 Watts into 4-8 ohm impedance speakers.
Features
- Volume trim pot so you can set/adjust the amount of amplification on the board. This is a generic board - every install varies. There are 6 connections:
- Positive and negative speaker in
- Positive and negative speaker out
- Positive voltage connection. You will need to probe for a switched voltage source (only on when power switch on).
- Negative connection
- Note: the hole labeled "SD" is not used.
- Output Power: 2.5W at 4Ω, 10% THD, 1.5W at 8Ω, 10% THD, with 5.5V Supply
* 50dB PSRR at 1KHz
* Filterless design, with ferrite bead + capacitors on output.
* Fixed 24dB gain, onboard trim potentiometer for adjusting input volume.
* Thermal and short-circuit/over-current protection
* Low current draw: 4mA quiescent and 1uA in shutdown mode
Notes
These parts are not mass produced and we use multiple machine shops, so surface finish, texture, and color may vary between batches. Colors may also look different depending on your screen, the lighting, and variations in anodizing.
Please be sure to review our refund policy for cancelled and returned orders.
We cannot change the value of the shipment and sadly we do not have control over your particular country's fee/tariffs/taxes.
Brass parts come as machined and may show oxidation/discolor (due to being exposed to air) and some small machining or small scratches may be present. Assume you will need to do your final surface finishing using a flexible 3M sanding pad. (The 3M 7448 usually works well). After polishing, clean and apply clearcoat, poly, or other coating to maintain the shine. Note Brass is also very dense (heavy) and conductive. Consider in some applications, these attributes may have adverse effects. (ex. The SP hinges will not support the screen as well). If used with electronics, it is advisable to use kapton tape, insulating paint, (nail polish may work) to prevent electrical shorts.
Resources
Out of stock? Signup for our out of stock notification on this product page and check our product availability page
Assembly Instructions
International Customers
We are located in the USA, and want everyone in the world to experience Boxy Pixel products worldwide! It is important to understand a few points:
1. There are two shipping methods available. DHL and USPS (United States Postal Service). DHL is very fast and comes with insurance, but can be expensive. The USPS slow shipping we offer can take many weeks, is not reliable, and is not insured.
2. If you do choose uninsured USPS for your international shipping, we do offer third party insurance to help in case it gets lost. This is "route" insurance. It is not expensive, and is worth the cost. Deselecting this option at checkout will waive all insurance. If your package is lost, we unfortunately cannot send a refund or replacement.
3. If an item gets shipped back to us due to delivery problems, we would need to charge additional fees if you would like to attempt delivery again.
4. Return shipping is the responsibility of the buyer
5. We are prohibited from shipping batteries outside of the USA.
These parts are not mass produced and we use multiple machine shops, so surface finish, texture, and color may vary between batches. Colors may also look different depending on your screen, the lighting, and variations in anodizing.
Please be sure to review our refund policy for cancelled and returned orders.
We cannot change the value of the shipment and sadly we do not have control over your particular country's fee/tariffs/taxes.
Brass parts come as machined and may show oxidation/discolor (due to being exposed to air) and some small machining or small scratches may be present. Assume you will need to do your final surface finishing using a flexible 3M sanding pad. (The 3M 7448 usually works well). After polishing, clean and apply clearcoat, poly, or other coating to maintain the shine. Note Brass is also very dense (heavy) and conductive. Consider in some applications, these attributes may have adverse effects. (ex. The SP hinges will not support the screen as well). If used with electronics, it is advisable to use kapton tape, insulating paint, (nail polish may work) to prevent electrical shorts.
Out of stock? Signup for our out of stock notification on this product page and check our product availability page
Assembly Instructions
We are located in the USA, and want everyone in the world to experience Boxy Pixel products worldwide! It is important to understand a few points:
1. There are two shipping methods available. DHL and USPS (United States Postal Service). DHL is very fast and comes with insurance, but can be expensive. The USPS slow shipping we offer can take many weeks, is not reliable, and is not insured.
2. If you do choose uninsured USPS for your international shipping, we do offer third party insurance to help in case it gets lost. This is "route" insurance. It is not expensive, and is worth the cost. Deselecting this option at checkout will waive all insurance. If your package is lost, we unfortunately cannot send a refund or replacement.
3. If an item gets shipped back to us due to delivery problems, we would need to charge additional fees if you would like to attempt delivery again.
4. Return shipping is the responsibility of the buyer
5. We are prohibited from shipping batteries outside of the USA.
Give your Classic electronics a new life!
Unique
Parts cut from a solid block of billet aluminum
Protection
Each part is anodized for long lasting protection